What You should Know about Wooden Fence Gate


What You should Know about Wooden Fence Gate

One must take into account a few problems that are presented when selecting wood gates as their material of choice. The gate itself will be the first section of the fence to fail, despite the fact that a decent wooden fence may be built that can survive for ten to twenty years with no more maintenance than the occasional refinishing or replacement of a picket that has become bent.

Gates made entirely of wood, including the rails with diagonal bracing, have a propensity to droop, either inside the frame itself or as a result of the bolts used in the hinges "pulling" through the wood. This is owing to the "soft character" of fence wood, such as red cedar, which causes it to be easily damaged. Despite the fact that cedar will be resistant to decay, the wood is very soft, and nuts and bolts have a tendency to "pull" through it with time.

Wooden Fence Gates

Because of this, we take a lot of precautions while building fences out of wood. Every junction on the 2 by 4 structure is covered with shiplap, and galvanized carriage bolts, two for each corner or bracing, are used to secure it.

It not only offers the highest possible level of protection against sagging, but it also creates an appealing gate that has the appearance of having been well created, in contrast to a gate that is just made up of three rails as well as a diagonal bracing that has been tacked on.

We utilize three horizontal rails on gates that are between 5 and 7 feet high. When the height is less than four feet, we employ two horizontal rails. In addition to this, there are two vertical outer frame rails that are employed to create the outside rectangle frame.

At each corner, a groove is cut so that the intersecting rails sit flat against one another, and then two bolts are inserted into each corner. To assist in delaying the onset of drooping, a diagonal 1 x 4 or any other appropriate other cedar matching piece is utilized as a diagonal bracing.



Wooden Fence Gates

This brace is routed into the 2 by 4 frame as well to produce a strong connection that is aesthetically pleasing. Additionally, it is secured with two bolts for each connection it makes. When constructing a gate with three rails, the diagonal also gets routed then attached to the central rail.

The only additional safety measure that should be taken is to fasten the hinges to the posts or the fence using large bolts. The vast majority of hinge sets do not come with bolts of sufficient length. It is necessary for the side bolts of the gate to be nutted after passing through the pickets and rails of the gate.

Lag bolts, which are often included with the majority of hinge sets, may ultimately come out of the soft cedar or other wood that is utilized if they are not secured properly. Even in more durable treated wood fences, bolts will ultimately break, no matter how well you maintain them.

Wooden Fence Gates


The very finest gates feature steel frames that have been welded together, and wood pickets that are affixed to the frame. These gates, unlike all other wood-framed gates, will not sag with time.

The gate's structure is similar to the one made of wood, but there is no diagonal support since the gate is so thin.

Wooden Fence Gates

Because there are so many distinct fence designs, the dimensions of the steel frames and bracing, as well as their arrangement, may vary quite a little. The gate must have an increased amount of diagonal bracing if it is both wider and higher.

The more affordable steel frames are made of galvanized fence tubing that has been notched at each weld to give the illusion of being tidy and professional.

The normal outside diameter of the pipe used is 2 inches. The wall thickness of a gate may vary depending on its usage, style, and size. This galvanized pipe frame is often not painted to match the wood since it is galvanized throughout.

Although it is not as aesthetically pleasing as the version that costs more money, it is quite durable and useful and does not cost too much.

Because the welds would destroy the factory galvanized finish, a special paint designed to galvanize metal is added after the welding process in order to prevent the metal from rusting.

The painted welds need to be touched up every three to five years since the paint does not perform as well as the galvanizing did initially.

Wooden Fence Gates

A steel framework that is formed of 2 x 3 or 2 x 4 steel stock has a more appealing appearance since it comes close to replicating the look of the wooden rails that make up the remainder of the fence.

To maintain the look of wood, the steel is often coated brown to match the color of the wood. When ordered, it may be painted in whatever color the customer desires. The tubular form of gate will be less expensive than this framed version of the gate.

Wooden Fence Gates


Wood gates may be constructed in any size, up to their maximum capacity. When working with wood, the gate should never be made any broader than required. If a walk gate that is 3 feet wide is sufficient, you may omit the waste space of 1 foot on the rails and make it 3 feet long instead (2 x 4s are typically 8 feet long). Each foot adds more weight, which over time will cause the gate to become more prone to drooping. Use a double swing gate for any opening that is at least 6 feet wide. The entrance size of 16 feet is the maximum width that may be achieved with wood gate frames. These gates need to be equipped with a leading edge roller so that the gate may be supported properly on each leaf.

Larger wood picket gates can be built, but the use of steel frames is the only way to guarantee that the finished product will be adequate. The following information is provided to assist you in making a decision about width. Because the width of your front entrance cannot be more than 36 inches, you should select gates that are at least that broad.

Wooden Fence Gates

Your home appliance will not be able to pass past the gate into the residence that you wish to utilize. A clearance of at least 12 feet should be maintained through the gate of a driveway. 14' is better. This opens up only one lane for traffic. The majority of roadways are barely ten feet wide, yet the average speed on them is sixty-five miles per hour.

Therefore, the minimum width for a driveway with two lanes should be 22 feet. 24' is better. However, we ask that you do not go at a speed of 65 miles per hour in that vehicle.

Consider the turning radius if your gate is located near the road and large vehicles such as lorries and trailers must enter. A 40' trailer needs a large radius. On existing driveways, tire tracks may often be seen leading off the driveway in various directions. It is strongly recommended that you measure from the tire tracks rather than the driveway. It is inevitable that someone will strike the gatepost.

Wooden Fence Gates

It could be a good idea to move the gate farther away from the road. It is possible for a front fence to extend all the way to the road right of way; but, if you slant the fence back on the edges of the driveway, you will have enough room for the gate to be put back by 15–20 feet.

This not only results in a larger turning radius, but it also makes it possible for a vehicle to pull into the drive without the driver needing to stop in the roadway to unlock the gate. It is not required to make the gates any wider than they already are. It will simply lead to more complications.


Think about how much heavier wooden gates are. They might end up being fairly weighty. If young children have access to the gate as well as the latch or hinge side both allow for pinch points, then it is possible for a kid to sustain serious injuries from a gate that is shutting too quickly.




Wooden Fence Gates

Install jams on the inside of the gate to prevent young children's fingers from getting caught in the hinge side fissures while the gate is open. Leave a sufficient amount of room on the side of the latch so that young children's fingers won't be able to get stuck in the little pinch points.

Remember that if there is a lot of wind outside, the gate will turn into a sail, and a youngster will not be able to open or shut it. Think about leaving gaps between the pickets so that air may move freely through the structure. Never allow two kids to "play" with the gate at the same time. When one is slammed on someone who is unaware of its presence, it will do harm to the other.

Wooden Fence Gates